AnyTech

With Box and User Manual. With Ethernet Port (RJ45), RS232 port for external Modem and built-in Web server.

Attachments

CWM02.jpg: You don't have permission to download attachments.; (2 Kb) Downloaded 1 times

This allows Comfort to send commands to the Velbus modules and allows velbus modules to send status and commands to Comfort counters. as well as temperature information to Comfort sensor registors.

Attachments

ucm_velbus.jpg: You don't have permission to download attachments.; (102 Kb) Downloaded 0 times

UCM/232 is the RS232 serial interface which is connected to the computer and is required for uploading and downloading programmed configurations to Comfort using the Comfigurator software (downloadable from Software). The UCM/232 includes the IR Learner which is used to learn Infrared codes from any handheld remote control, for later transmission from any output connected to an IR Transmitter …

Attachments

126-ucmrs232-2 small.jpg: You don't have permission to download attachments.; (5 Kb) Downloaded 0 times

[ Διαβάστε ολόκληρο το θέμα ]

Allows Comfort to communicate with C-BUS to send commands to any group address as well as receive status and commands. The C-BUS bus cable terminates onto the UCM/CBUS module. The CBUS PC Interface is not required.

Attachments

75-CBUS.jpg: You don't have permission to download attachments.; (4 Kb) Downloaded 0 times

UCM Interface to Honeywell Smartft Temperature Control System. Allows Comfort to communicate with Honeywell Smartfit to read room and water temperature and to override setpoints.

Attachments

ucm_smartfit.jpg: You don't have permission to download attachments.; (4 Kb) Downloaded 0 times

Allows Comfort to communicate with KNX to send telegrams to any group address as well as receive status and commands from the KNX. The EIB bus cable terminates onto the UCM/KNX module.

Attachments

76-EIB.jpg: ucm/knx; You don't have permission to download attachments.; (5 Kb) Downloaded 0 times

Acts as a backup dialer when the landline is down or cut.
Dials to SMS with alarm type and zone or other information.
Send SMS from users mobile to control Comfort.
Dial to GSM number to control Comfort.
SIM card is required.

Attachments

gsm2.jpg: ucm/gsm2; You don't have permission to download attachments.; (5 Kb) Downloaded 0 times

UCM/Ethernet is the interface which is connected to the Local Area Network and is used for uploading and downloading programmed configurations to Comfort using the Comfigurator software (downloadable from Software). This also includes a RS232 interface selectable by jumper. The UCM/Ethernet includes the IR Learner which is used to learn Infrared codes from any handheld remote control, for later …

Attachments

77-ucm_ethernet_sm.jpg: ucm/eth; You don't have permission to download attachments.; (4 Kb) Downloaded 0 times

[ Διαβάστε ολόκληρο το θέμα ]

Κύρια χαρακτηριστικά:

* 8 Inputs/8 Outputs expandable to 64 Inputs/64 Outputs via Slaves
* Addtional 64 Inputs/64 Outputs via RIO/SCS
* 6 Control groups, each with 10 device menus, each with 10 actions
* Full Duplex Intercom between Phones and Keypad/Door Stations (KP03, KP04 and DP03)
* 1023 Responses with 8 bytes per Response for programming
* 250 Events in Event Log
* 4096 …

Attachments

5-cm9000sm.jpg: Main Panel; You don't have permission to download attachments.; (3 Kb) Downloaded 0 times

[ Διαβάστε ολόκληρο το θέμα ]